摘要：Maxim的1-Wire?器件都帶有一個64位的唯一注冊碼，存儲在只讀存儲器內(ROM)，能夠在1-Wire網絡中通過1-Wire主機對其尋址。如果1-Wire網絡中從機器件的ROM碼是未知的，則可采用搜索算法查找這些碼。本文詳細說明了搜索算法的原理，并提供了一個范例，便于用戶使用。該算法對任何現有的或?qū)⒁瞥龅?-Wire器件都是有效的。

緒論

Maxim的每片1-Wire器件都有唯一的64位注冊碼，它存儲在只讀存儲器(ROM)中。在1-Wire網絡中，注冊碼用于1-Wire主機對從機器件進行逐一尋址。如果1-Wire網絡中從機器件的ROM碼是未知的，可以通過搜索算法來找到此碼。本文不僅詳細地解釋了搜索算法，而且還提供了實現快速整合的例程。該算法適用于任何具有1-Wire接口特性的現有產品及未來產品。


圖1. 64位唯一的ROM注冊碼

搜索算法

搜索算法采用的是二叉樹型結構，搜索過程沿各分節點進行，直到找到器件的ROM碼即葉子為止；后續的搜索操作沿著節點上的其它路徑進行，按照同樣的方式直到找到總線上的所有器件代碼。

搜索算法首先通過復位(reset)和在線應答脈沖(presence pulse)時隙將1-Wire總線上的所有器件復位；成功地執行該操作后，發送1 個字節的搜索命令；搜索命令使1-Wire器件準備就緒、開始進行搜索操作。

搜索命令分為兩類：標準搜索命令(F0 hex)用來搜索連接到網絡中所有器件；報警或有條件搜索命令(EC hex)只用來搜索那些處于報警狀態下的器件，這種方式縮小了搜索范圍，可以快速查找到所需要注意的器件。

搜索命令發出之后，開始實際的搜索過程。首先總線上的所有從機器件同時發送ROM碼(也叫注冊碼)中的第一位(最低有效位) (參見圖1)。與所有的1-Wire通信一樣，無論是讀取數據還是向從機器件寫數據，都由1-Wire主機啟動每一位操作。按照1-Wire的特性，當所有從機器件同時應答主機時，結果相當于全部發送數據位的邏輯AND；從機發送其ROM碼的第一位后，主機啟動下一位操作、接著從機發送第一位數據的補碼；從兩次讀到的數據位可以對ROM碼的第一位做出幾種判斷(參見表1)。

表1. 檢索信息位

Bit (true)	Bit (complement)	Information Known
0	0	There are both 0s and 1s in the current bit position of the participating ROM numbers. This is a discrepancy.
0	1	There are only 0s in the bit of the participating ROM numbers.
1	0	There are only 1s in the bit of the participating ROM numbers.
1	1	No devices participating in search.

按照搜索算法的要求，1-Wire主機必須向總線上的從機發回一個指定位；如果從機器件中ROM碼的當前位的值與該數據位匹配，則繼續參與搜索過程；若從機器件的當前位與之不匹配，則該器件轉換到等待狀態，并保持等待狀態直到下一個1-Wire復位信號到來。其余63位ROM碼的搜索依然按照這種‘讀兩位’、‘寫一位’的模式進行重復操作(參見表2)。按照這種搜索算法進行下去，最終除了一個從機器件外所有從機將進入等待狀態，經過最后一輪檢測，就可得到最后保留(未進入等待狀態)器件的ROM碼。在后續搜索過程中，選用不同的路徑(或分支)來查找其它器件的ROM碼。需要注意的是本文ROM碼的數據位用第1位(最低有效位)到第64 位(最高有效位)表示，而不是我們常用的那種第0位到第63位的模式；這樣設置允許將差異位置計數器初始值置為0，為以后的比較提供了方便。

表2. 1-Wire主機和從機的搜索過程

Master	Slave
1-Wire reset stimulus	Produce presence pulse
Write search command (normal or alarm)	Each slave readies for search.
Read 'AND' of bit 1	Each slave sends bit 1 of its ROM number.
Read 'AND' of complement bit 1	Each slave sends complement bit 1 of its ROM number.
Write bit 1 direction (according to algorithm)	Each slave receives the bit written by master, if bit read is not the same as bit 1 of its ROM number then go into a wait state.
?	?
?	?
?	?
Read 'AND' of bit 64	Each slave sends bit 64 of its ROM number.
Read 'AND' of complement bit 64	Each slave sends complement bit 64 of its ROM number.
Write bit 64 direction (according to algorithm)	Each slave receives the bit written by master, if bit read is not the same as bit 64 of its ROM number then go into a wait state.

從表1可以看出：如果所有總線上的器件在當前位具有相同值，那么只有一條分支路徑可選；總線上沒有器件響應的情況是一種異常狀態，可能是要查找的器件在搜尋過程中與1-Wire總線脫離。如果出現這種情況，應中止搜索，并發出1-Wire復位信號起始新的搜索過程。如果當前位既有0也有1，這種情況稱為位值差異，它對在后續搜索過程中查找器件起關鍵作用。搜索算法指定在第一輪查詢中若出現差異(數據位/補碼 = 0/0)，則選用‘0’路徑。注意：這一點是由本文檔中介紹的特定算法決定的，其它算法中或許首先選用‘1’路徑。記錄最后一次值差異的位置以供下一次搜索使用，表3列出了出現值差異時路徑的選取情況。

表3. 搜索路徑方向

Search Bit Position vs Last Discrepancy	Path Taken
=	take the '1' path
<	take the same path as last time (from last ROM number found)
>	take the '0' path

搜索算法計算還對最初8位過程中出現的最后一次位差異保持跟蹤；64位注冊碼的前8位是家族碼，在器件的搜索過程中可以按照其家族碼進行分類。記錄家族碼的最后一次差異可以用于有選擇性地跳過1-Wire器件的整個分組。如需進行選擇性的搜索，可參考關于高級變量搜索的詳細解釋。64位ROM碼中包含8位循環冗余校驗碼(CRC)；CRC值用于驗證是否搜索到正確的ROM碼。ROM碼的排列如圖1所示。

DS2480B系列串口到1-Wire線路的驅動程序在硬件中實現了部分與本文檔中相同的搜索算法；詳細資料請參閱DS2480B數據資料和應用筆記192，DS2480B串行接口1-Wire線驅動器的使用的詳細介紹；從DS2490 USB口到1-Wire橋接器硬件電路中實現了整個搜索過程。

圖2列出了對一個從器件進行搜索的流程圖；注意：右側Reference欄對在流程圖中出現的符號進行了說明；在本文檔的源代碼附錄中也將用到這些專用符號。


圖2. 搜索流程


圖2. 搜索流程，第2部分

搜索算法通過對LastDiscrepancy、LastFamilyDiscrepancy、LastDeviceFlag和ROM_NO值(參見表4)的處理，利用上述流程實現了兩個不同類型的搜索操作；這兩個操作是搜索1-Wire器件ROM碼的基礎。

First

‘FIRST’操作是搜索1-Wire總線上的第一個從機器件。該操作是通過將LastDiscrepancy、 LastFamilyDiscrepancy和LastDeviceFlag置零，然后進行搜索完成的。最后ROM碼從ROM_NO寄存器中讀出。若1-Wire總線上沒有器件，復位序列就檢測不到應答脈沖，搜索過程中止。

Next

‘NEXT’操作是搜索1-Wire總線上的下一個從機器件；一般情況下，此搜索操作是在‘FIRST’操作之后或上一次‘NEXT’操作之后進行；保持上次搜索后這些值的狀態不變、執行又一次搜索即可實現‘NEXT’操作。之后從ROM_NO寄存器中來讀出新一個ROM碼。若前一次搜索到的是1-Wire上的最后一個器件，則返回一個無效標記FALSE，并且把狀態設置成下一次調用搜索算法時將是‘FIRST’操作的狀態。

圖3 (a, b, c)例舉了三個器件的搜索過程，為便于說明，設器件的ROM碼只有2位。






圖3. 搜索過程舉例

高級變量搜索

有3種利用同一組狀態變量LastDiscrepancy、LastFamilyDiscrepancy、LastDeviceFlag、ROM_NO實現的高級變量搜索算法，這幾種高級搜索算法允許來指定作為搜索目標或需要跳過搜索的器件的類型(家族碼)以及驗證某類型的器件是否在線(參見表4)。

Verify

‘VERIFY’操作用來檢驗已知ROM碼的器件是否連接在1-Wire總線上，通過提供ROM碼并對該碼進行目標搜索就可確定此器件是否在線。首先，將ROM_NO寄存器值設置為已知的ROM碼值，然后將LastDiscrepancy和LastDeviceFlag標志位分別設置為64 (40h)和0； 進行搜索操作，然后讀ROM_NO的輸出結果；如果搜索成功并且ROM_NO中存儲的仍是要搜索器件的ROM碼值，那么此器件就在1-Wire總線上。

Target Setup

‘TARGET SETUP’操作就是用預置搜索狀態的方式首先查找一個特殊的家族類型，每個1-Wire器件都有一個字節的家族碼內嵌在ROM碼中(參見圖1)，主機可以通過家族碼來識別器件所具有的特性和功能。若1-Wire總線上有多片器件時，通常是將搜索目標首先定位在需注意的器件類型上。為了將一個特殊的家族作為搜索目標，需要將所希望的家族碼字節放到ROM_NO寄存器的第一個字節中，并且將ROM_NO寄存器的復位狀態置零，然后將LastDiscrepancy設置為64 (40h)；把LastDeviceFlag和LastFamilyDiscrepancy設置為0。在執行下一次搜索算法時就能找出所期望的產品類型的第一個器件；并將此值存入ROM_NO寄存器。需要注意的是如果1-Wire總線上沒有掛接所期望的產品類型的器件，就會找出另一類型的器件，所以每次搜索完成后，都要對ROM_NO寄存器中存儲的結果進行校驗。

Family Skip Setup

‘FAMILY SKIP SETUP’操作用來設置搜索狀態以便跳過搜索到的指定家族中的所有器件，此操作只有在一個搜索過程結束后才能使用。通過把LastFamilyDiscrepancy復制到LastDiscrepancy，并清除LastDeviceFlag即可實現該操作；在下一搜索過程就會找到指定家族中的下一個器件。如果當前家族碼分組是搜索過程中的最后一組，那么搜索過程結束并將LastDeviceFlag置位。

表4. 搜索變量狀態的設置

?	LastDiscrepancy	LastFamily- Discrepancy	LastDeviceFlag	ROM_NO
FIRST	0	0	0	result
NEXT	leave unchanged	leave unchanged	leave unchanged	result
VERIFY	64	0	0	set with ROM to verify, check if same after search
TARGET SETUP	64	0	0	set first byte to family code, set rest to zeros
FAMILY SKIP SETUP	copy from LastFamilyDiscrepancy	0	0	leave unchanged

結論

本文提供的搜索算法可以找出任意給定的1-Wire器件組中獨一無二的ROM碼，這是保證多點1-Wire總線應用的關鍵，已知ROM碼后就可以對逐一選定的某個1-Wire器件來進行操作。本文還對一些變量搜索算法做了詳細論述，這些變量搜索算法能夠查找或跳過特定類型的1-Wire器件。附錄給出了實現搜索過程和所有變量搜索算法的例程，并給出了‘C’程序代碼。

附錄

下面給出了搜索算法的‘C’程序代碼及實現每個變量搜索算法的函數。FamilySkipSetup和TargetSetup函數實際上并沒有進行搜索操作，它們只不過是用來設置搜索寄存器，以便在下一次執行‘NEXT’操作時能跳過或找到所期望的類型。需要注意的是低級1-Wire函數可通過調用TMEX API實現。這些程序調用只是用于系統測試，也可以用特定平臺調用。關于TMEX API和其它一些1-Wire API的詳細資料請參考應用筆記155。

下列TMEX API測試程序的源代碼可從Maxim網頁下載。

// TMEX API TEST BUILD DECLARATIONS
#define TMEXUTIL
#include "ibtmexcw.h"
long session_handle;
// END TMEX API TEST BUILD DECLARATIONS

// definitions
#define FALSE 0
#define TRUE  1

// method declarations
int  OWFirst();
int  OWNext();
int  OWVerify();
void OWTargetSetup(unsigned char family_code);
void OWFamilySkipSetup();
int  OWReset();
void OWWriteByte(unsigned char byte_value);
void OWWriteBit(unsigned char bit_value);
unsigned char OWReadBit();
int  OWSearch();
unsigned char docrc8(unsigned char value);

// global search state
unsigned char ROM_NO[8];
int LastDiscrepancy;
int LastFamilyDiscrepancy;
int LastDeviceFlag;
unsigned char crc8;

//--------------------------------------------------------------------------
// Find the 'first' devices on the 1-Wire bus
// Return TRUE  : device found, ROM number in ROM_NO buffer
//        FALSE : no device present
//
int OWFirst()
{
   // reset the search state
   LastDiscrepancy = 0;
   LastDeviceFlag = FALSE;
   LastFamilyDiscrepancy = 0;

   return OWSearch();
}

//--------------------------------------------------------------------------
// Find the 'next' devices on the 1-Wire bus
// Return TRUE  : device found, ROM number in ROM_NO buffer
//        FALSE : device not found, end of search
//
int OWNext()
{
   // leave the search state alone
   return OWSearch();
}

//--------------------------------------------------------------------------
// Perform the 1-Wire Search Algorithm on the 1-Wire bus using the existing
// search state.
// Return TRUE  : device found, ROM number in ROM_NO buffer
//        FALSE : device not found, end of search
//
int OWSearch()
{
   int id_bit_number;
   int last_zero, rom_byte_number, search_result;
   int id_bit, cmp_id_bit;
   unsigned char rom_byte_mask, search_direction;

   // initialize for search
   id_bit_number = 1;
   last_zero = 0;
   rom_byte_number = 0;
   rom_byte_mask = 1;
   search_result = 0;
   crc8 = 0;

   // if the last call was not the last one
   if (!LastDeviceFlag)
   {
      // 1-Wire reset
      if (!OWReset())
      {
         // reset the search
         LastDiscrepancy = 0;
         LastDeviceFlag = FALSE;
         LastFamilyDiscrepancy = 0;
         return FALSE;
      }

      // issue the search command 
      OWWriteByte(0xF0);  

      // loop to do the search
      do
      {
         // read a bit and its complement
         id_bit = OWReadBit();
         cmp_id_bit = OWReadBit();

         // check for no devices on 1-wire
         if ((id_bit == 1) && (cmp_id_bit == 1))
            break;
         else
         {
            // all devices coupled have 0 or 1
            if (id_bit != cmp_id_bit)
               search_direction = id_bit;  // bit write value for search
            else
            {
               // if this discrepancy if before the Last Discrepancy
               // on a previous next then pick the same as last time
               if (id_bit_number < LastDiscrepancy)
                  search_direction = ((ROM_NO[rom_byte_number] & rom_byte_mask) > 0);
               else
                  // if equal to last pick 1, if not then pick 0
                  search_direction = (id_bit_number == LastDiscrepancy);

               // if 0 was picked then record its position in LastZero
               if (search_direction == 0)
               {
                  last_zero = id_bit_number;

                  // check for Last discrepancy in family
                  if (last_zero < 9)
                     LastFamilyDiscrepancy = last_zero;
               }
            }

            // set or clear the bit in the ROM byte rom_byte_number
            // with mask rom_byte_mask
            if (search_direction == 1)
              ROM_NO[rom_byte_number] |= rom_byte_mask;
            else
              ROM_NO[rom_byte_number] &= ~rom_byte_mask;

            // serial number search direction write bit
            OWWriteBit(search_direction);

            // increment the byte counter id_bit_number
            // and shift the mask rom_byte_mask
            id_bit_number++;
            rom_byte_mask <<= 1;

            // if the mask is 0 then go to new SerialNum byte rom_byte_number and reset mask
            if (rom_byte_mask == 0)
            {
                docrc8(ROM_NO[rom_byte_number]);  // accumulate the CRC
                rom_byte_number++;
                rom_byte_mask = 1;
            }
         }
      }
      while(rom_byte_number < 8);  // loop until through all ROM bytes 0-7

      // if the search was successful then
      if (!((id_bit_number < 65) || (crc8 != 0)))
      {
         // search successful so set LastDiscrepancy,LastDeviceFlag,search_result
         LastDiscrepancy = last_zero;

         // check for last device
         if (LastDiscrepancy == 0)
            LastDeviceFlag = TRUE;
         
         search_result = TRUE;
      }
   }

   // if no device found then reset counters so next 'search' will be like a first
   if (!search_result || !ROM_NO[0])
   {
      LastDiscrepancy = 0;
      LastDeviceFlag = FALSE;
      LastFamilyDiscrepancy = 0;
      search_result = FALSE;
   }

   return search_result;
}

//--------------------------------------------------------------------------
// Verify the device with the ROM number in ROM_NO buffer is present.
// Return TRUE  : device verified present
//        FALSE : device not present
//
int OWVerify()
{
   unsigned char rom_backup[8];
   int i,rslt,ld_backup,ldf_backup,lfd_backup;

   // keep a backup copy of the current state
   for (i = 0; i < 8; i++)
      rom_backup[i] = ROM_NO[i];
   ld_backup = LastDiscrepancy;
   ldf_backup = LastDeviceFlag;
   lfd_backup = LastFamilyDiscrepancy;

   // set search to find the same device
   LastDiscrepancy = 64;
   LastDeviceFlag = FALSE;

   if (OWSearch())
   {
      // check if same device found
      rslt = TRUE;
      for (i = 0; i < 8; i++)
      {
         if (rom_backup[i] != ROM_NO[i])
         {
            rslt = FALSE;
            break;
         }
      }
   }
   else
     rslt = FALSE;

   // restore the search state 
   for (i = 0; i < 8; i++)
      ROM_NO[i] = rom_backup[i];
   LastDiscrepancy = ld_backup;
   LastDeviceFlag = ldf_backup;
   LastFamilyDiscrepancy = lfd_backup;

   // return the result of the verify
   return rslt;
}

//--------------------------------------------------------------------------
// Setup the search to find the device type 'family_code' on the next call
// to OWNext() if it is present.
//
void OWTargetSetup(unsigned char family_code)
{
   int i;

   // set the search state to find SearchFamily type devices
   ROM_NO[0] = family_code;
   for (i = 1; i < 8; i++)
      ROM_NO[i] = 0;
   LastDiscrepancy = 64;
   LastFamilyDiscrepancy = 0;
   LastDeviceFlag = FALSE;
}

//--------------------------------------------------------------------------
// Setup the search to skip the current device type on the next call
// to OWNext().
//
void OWFamilySkipSetup()
{
   // set the Last discrepancy to last family discrepancy
   LastDiscrepancy = LastFamilyDiscrepancy;
   LastFamilyDiscrepancy = 0;

   // check for end of list
   if (LastDiscrepancy == 0)
      LastDeviceFlag = TRUE;
}

//--------------------------------------------------------------------------
// 1-Wire Functions to be implemented for a particular platform
//--------------------------------------------------------------------------

//--------------------------------------------------------------------------
// Reset the 1-Wire bus and return the presence of any device
// Return TRUE  : device present
//        FALSE : no device present
//
int OWReset()
{
   // platform specific
   // TMEX API TEST BUILD
   return (TMTouchReset(session_handle) == 1);
}

//--------------------------------------------------------------------------
// Send 8 bits of data to the 1-Wire bus
//
void OWWriteByte(unsigned char byte_value)
{
   // platform specific
   
   // TMEX API TEST BUILD
   TMTouchByte(session_handle,byte_value);
}

//--------------------------------------------------------------------------
// Send 1 bit of data to teh 1-Wire bus
//
void OWWriteBit(unsigned char bit_value)
{
   // platform specific

   // TMEX API TEST BUILD
   TMTouchBit(session_handle,(short)bit_value);
}

//--------------------------------------------------------------------------
// Read 1 bit of data from the 1-Wire bus 
// Return 1 : bit read is 1
//        0 : bit read is 0
//
unsigned char OWReadBit()
{
   // platform specific

   // TMEX API TEST BUILD
   return (unsigned char)TMTouchBit(session_handle,0x01);

}

// TEST BUILD
static unsigned char dscrc_table[] = {
        0, 94,188,226, 97, 63,221,131,194,156,126, 32,163,253, 31, 65,
      157,195, 33,127,252,162, 64, 30, 95,  1,227,189, 62, 96,130,220,
       35,125,159,193, 66, 28,254,160,225,191, 93,  3,128,222, 60, 98,
      190,224,  2, 92,223,129, 99, 61,124, 34,192,158, 29, 67,161,255,
       70, 24,250,164, 39,121,155,197,132,218, 56,102,229,187, 89,  7,
      219,133,103, 57,186,228,  6, 88, 25, 71,165,251,120, 38,196,154,
      101, 59,217,135,  4, 90,184,230,167,249, 27, 69,198,152,122, 36,
      248,166, 68, 26,153,199, 37,123, 58,100,134,216, 91,  5,231,185,
      140,210, 48,110,237,179, 81, 15, 78, 16,242,172, 47,113,147,205,
       17, 79,173,243,112, 46,204,146,211,141,111, 49,178,236, 14, 80,
      175,241, 19, 77,206,144,114, 44,109, 51,209,143, 12, 82,176,238,
       50,108,142,208, 83, 13,239,177,240,174, 76, 18,145,207, 45,115,
      202,148,118, 40,171,245, 23, 73,  8, 86,180,234,105, 55,213,139,
       87,  9,235,181, 54,104,138,212,149,203, 41,119,244,170, 72, 22,
      233,183, 85, 11,136,214, 52,106, 43,117,151,201, 74, 20,246,168,
      116, 42,200,150, 21, 75,169,247,182,232, 10, 84,215,137,107, 53};

//--------------------------------------------------------------------------
// Calculate the CRC8 of the byte value provided with the current 
// global 'crc8' value. 
// Returns current global crc8 value
//
unsigned char docrc8(unsigned char value)
{
   // See Application Note 27
   
   // TEST BUILD
   crc8 = dscrc_table[crc8 ^ value];
   return crc8;
}

//--------------------------------------------------------------------------
// TEST BUILD MAIN
//
int main(short argc, char **argv)
{
   short PortType=5,PortNum=1;
   int rslt,i,cnt;

   // TMEX API SETUP
   // get a session
   session_handle = TMExtendedStartSession(PortNum,PortType,NULL);
   if (session_handle <= 0)
   {
      printf("No session, %d\n",session_handle);
      exit(0);
   }

   // setup the port
   rslt = TMSetup(session_handle);
   if (rslt != 1)
   {
      printf("Fail setup, %d\n",rslt);
      exit(0);
   }
   // END TMEX API SETUP

   // find ALL devices
   printf("\nFIND ALL\n");
   cnt = 0;
   rslt = OWFirst();
   while (rslt)
   {
      // print device found
      for (i = 7; i >= 0; i--)
         printf("%02X", ROM_NO[i]);
      printf("  %d\n",++cnt);

      rslt = OWNext();
   }

   // find only 0x1A
   printf("\nFIND ONLY 0x1A\n");
   cnt = 0;
   OWTargetSetup(0x1A);
   while (OWNext())
   {
      // check for incorrect type
      if (ROM_NO[0] != 0x1A)
         break;
      
      // print device found
      for (i = 7; i >= 0; i--)
         printf("%02X", ROM_NO[i]);
      printf("  %d\n",++cnt);
   }

   // find all but 0x04, 0x1A, 0x23, and 0x01
   printf("\nFIND ALL EXCEPT 0x10, 0x04, 0x0A, 0x1A, 0x23, 0x01\n");
   cnt = 0;
   rslt = OWFirst();
   while (rslt)
   {
      // check for incorrect type
      if ((ROM_NO[0] == 0x04) || (ROM_NO[0] == 0x1A) || 
          (ROM_NO[0] == 0x01) || (ROM_NO[0] == 0x23) ||
          (ROM_NO[0] == 0x0A) || (ROM_NO[0] == 0x10))
          OWFamilySkipSetup();
      else
      {
         // print device found
         for (i = 7; i >= 0; i--)
            printf("%02X", ROM_NO[i]);
         printf("  %d\n",++cnt);
      }

      rslt = OWNext();
   }

   // TMEX API CLEANUP
   // release the session
   TMEndSession(session_handle);
   // END TMEX API CLEANUP
}