#include "hidef.h"

#include "non_bank.sgm"
#include "runtime.sgm"

?

#ifndef __HCS12X__ /* it's different for the HCS12X. See the text below at the #else // __HCS12X__ */

/*
?? According to the -Cp option of the compiler the
?? __DPAGE__, __PPAGE__ and __EPAGE__ macros are defined.
?? If none of them is given as argument, then no page accesses should occur and
?? this runtime routine should not be used !
?? To be on the save side, the runtime routines are created anyway.
?? If some of the -Cp options are given an adapted versions which only covers the
?? needed cases is produced.
*/

/* if no compiler option -Cp is given, it is assumed that all possible are given : */

/* Compile with option -DHCS12 to activate this code */
#if defined(HCS12) || defined(_HCS12) || defined(__HCS12__) /* HCS12 family has PPAGE register only at 0x30 */
#define PPAGE_ADDR (0x30+REGISTER_BASE)
#ifndef __PPAGE__ /* may be set already by option -CPPPAGE */
#define __PPAGE__
#endif
/* Compile with option -DDG128 to activate this code */
#elif defined DG128 /* HC912DG128 derivative has PPAGE register only at 0xFF */
#define PPAGE_ADDR (0xFF+REGISTER_BASE)
#ifndef __PPAGE__ /* may be set already by option -CPPPAGE */
#define __PPAGE__
#endif
#elif defined(HC812A4)
/* all setting default to A4 already */
#endif

#if !defined(__EPAGE__) && !defined(__PPAGE__) && !defined(__DPAGE__)
/* as default use all page registers */
#define __DPAGE__
#define __EPAGE__
#define __PPAGE__
#endif

/* modify the following defines to your memory configuration */

#define EPAGE_LOW_BOUND?? 0x400u
#define EPAGE_HIGH_BOUND? 0x7ffu

#define DPAGE_LOW_BOUND?? 0x7000u
#define DPAGE_HIGH_BOUND? 0x7fffu

#define PPAGE_LOW_BOUND?? (DPAGE_HIGH_BOUND+1)
#define PPAGE_HIGH_BOUND? 0xBFFFu

#define REGISTER_BASE????? 0x0u
#ifndef DPAGE_ADDR
#define DPAGE_ADDR??????? (0x34u+REGISTER_BASE)
#endif
#ifndef EPAGE_ADDR
#define EPAGE_ADDR??????? (0x36u+REGISTER_BASE)
#endif
#ifndef PPAGE_ADDR
#define PPAGE_ADDR??????? (0x35u+REGISTER_BASE)
#endif

/*
? The following parts about the defines are assumed in the code of _GET_PAGE_REG :
? - the memory region controlled by DPAGE is above the area controlled by the EPAGE and
??? below the area controlled by the PPAGE.
? - the lower bound of the PPAGE area is equal to be the higher bound of the DPAGE area + 1
*/
#if EPAGE_LOW_BOUND >= EPAGE_HIGH_BOUND || EPAGE_HIGH_BOUND >= DPAGE_LOW_BOUND || DPAGE_LOW_BOUND >= DPAGE_HIGH_BOUND || DPAGE_HIGH_BOUND >= PPAGE_LOW_BOUND || PPAGE_LOW_BOUND >= PPAGE_HIGH_BOUND
#error /* please adapt _GET_PAGE_REG for this non default page configuration */
#endif

#if DPAGE_HIGH_BOUND+1 != PPAGE_LOW_BOUND
#error /* please adapt _GET_PAGE_REG for this non default page configuration */
#endif

/* this module does either control if any access is in the bounds of the specified page or */
/* ,if only one page is specified, just use this page. */
/* This behavior is controlled by the define USE_SEVERAL_PAGES. */
/* If !USE_SEVERAL_PAGES does increase the performance significantly */
/* NOTE : When !USE_SEVERAL_PAGES, the page is also set for accesses outside of the area controlled */
/*??????? by this single page. But this is should not cause problems because the page is restored to the old value before any other access could occur */

相關電子資料下載

• 6*4段位LCD液晶段碼屏驅動IC（芯片）：VK1024B資料簡介 145
• Nexperia 2N7002BK,215 N溝道MOSFET中文參數資料_封裝尺寸_焊腳說明 57
• 2.8寸觸摸串口屏配備WIFI/藍牙：搭載樂鑫ESP32-S3R8，資料開源 87
• 卡爾動力完成6億元A輪融資,加速L4級自動駕駛編隊技術商業化 1001
• 14*4LCD液晶段碼屏驅動芯片-VK1S56D資料分享 81
• Nexperia PDTC114ET,215中文資料 焊腳 封裝尺寸 138
• 突發！AMD機密資料被盜！ 491
• 創意挑戰丨從0自制“自平衡立方體”（分享開源資料） 577
• Ci24R1與Si24R1：2.4GHz數據通信芯片對比數據資料分析 231
• 英飛凌45m?雙通道高邊驅動器BTS5045-2EKA中文資料 442