一 概述

SCCK33112H6A是一款高精度、低功耗、可替代NTC / PTC熱敏電阻的數字溫度傳感器，可用于通信、計算機、消費類電子、環境、工業和儀器儀表應用中的溫度測量。SCCK33112H6A在-40°C至+125°C的正常工作范圍內，可提供≤±0.5℃的溫度精度，并具有良好的溫度線性度。SCCK33112H6A可提供擴展測溫模式，將測溫范圍擴展為-55℃至+150℃。SCCK33112H6A的額定工作電壓范圍為1.4V~5.5V，在整個工作范圍內最大靜態電流為10μA（測溫頻率4Hz時）。集成在芯片內部的12位ADC分辨率低至0.0625°C。SCCK33112H6A采用1.6mm×1.6mm的SOT563/DFNWB封裝，兼容SMBus和I2C接口，在一條總線上最多可掛載四個從機，并具有SMBus報警功能。

二 封裝示意圖

三 引腳和配置功能

四 芯片功能模式

1 連續轉換模式

SCCK33112H6A 的默認工作模式是連續轉換模式，典型轉換時間為 26ms。在此模式下芯片內部的ADC執行連續溫度轉換，將每次的測溫結果存儲于溫度寄存器，并覆蓋前次結果。配置寄存器中的轉換速率位CR1和CR0可將SCCK33112H6A 配置為 0.25Hz、1Hz、4Hz 或 8Hz 的轉換速率?？赏ㄟ^配置 CR1、CR0 以改變轉換速率，SCCK33112H6A 將在完成當次轉換后，掉電并等待由 CR1、CR0 設置的延時，之后再進行下次轉換，如圖3所示。CR1 和 CR0 的配置詳見表 1。

2 擴展模式(Extended Mode)

SCCK33112H6A 在正常測溫模式下測溫范圍為-40℃至+125℃。通過將配置寄存器中的EM位寫為1，可使SCCK33112H6A 進入擴展測溫模式，此時 SCCK33112H6A 的溫度寄存器和溫度限制寄存器均被配置為13位數據格式，以實現對高于+128℃的溫度測量。SCCK33112H6A 中的只讀溫度寄存器采用兩個字節來存儲測溫結果，如表 8、表9 所示。字節1 為MSB，字節2 為 LSB，高 12 位（擴展模式下為 13 位）用于指示溫度。當不需要 LSB 的溫度信息時可不必讀取LSB。SCCK33112H6A 測溫結果的數據格式在表 2 和表 3 中列出，其中 1LSB = 0.0625°C，負數以二進制補碼的形式表示。當上電或復位后，SCCK33112H6A 的溫度寄存器將被置為 00h，直到下一次溫度轉換完成。溫度寄存器中未使用的位始終讀為 0（下表中未給出）。

3 關 斷 模 式 (Shutdown Mode)

關斷模式通過關閉除串行接口以外的所有電路來降低芯片功耗，從而將芯片的電流降至低于0.5μA（典型值）。將配置寄存器中的 SD 位寫為 1，可開啟關斷模式；如此配置寄存器后，SCCK33112H6A 將在完成當次轉換后關斷。若想退出關斷模式，可將 SD 位寫為 0，SCCK33112H6A 將重新進入連續轉換模式。

4 單 次 轉 換 模 式 (One-Shot Mode)

SCCK33112H6A 可被配置為 One-Shot 模式。當 SCCK33112H6A 處于關斷模式時，向配置寄存器中的OS位寫1 可開啟單次溫度轉換。在溫度轉換期間 OS 位讀為 0。單次溫度轉換完成后，SCCK33112H6A 將重新返回關斷狀態，OS 位讀為 1。當不需要連續測溫時，此功能可大幅降低芯片功耗。由于 SCCK33112H6A 單次測溫時間僅需 26ms（典型值），因此可通過該模式實現更高的測溫速率。通過將SCCK33112H6A 連續以 One-Shot 模式進行測溫，可實現每秒 30 次甚至更多次的溫度測量。

5 報 警 功 能 (ALERT)

SCCK33112H6A 具有溫度報警功能，可選擇將配置寄存器中的 TM 位寫為 0 或1，從而將SCCK33112H6A配置為比較模式（Comparator Mode）或中斷模式（Interrupt Mode），以實現不同的報警功能。

在比較模式（TM=0）中，當測溫結果連續等于或超過溫度上限寄存器值 THIGH的次數，達到由配置寄存器中F1/F0位定義的值時（如表 4 所示），ALERT 引腳將被激活。ALERT 引腳將始終保持激活狀態，直到測溫結果連續低于溫度下限寄存器值 TLOW 的次數達到由 F1/F0 定義的值。在中斷模式（TM=1）中，當測溫結果連續等于或超過 THIGH 的次數達到由 F1/F0 定義的值時（如表4所示），ALERT 引腳將被激活。ALERT 引腳將始終保持激活狀態，直到讀取 SCCK33112H6A 的任何寄存器、或SCCK33112H6A 成功響應了 SMBus 報警命令、或 SCCK33112H6A 進入關斷模式后，ALERT 引腳狀態才會被清除。當 ALERT 引腳狀態被清除后，僅當測溫結果連續低于 TLOW的次數達到由 F1/F0 定義的值時，該引腳才會再次被激活并保持，此后 ALERT 引腳狀態再次被清除的條件同上。也可通過使用全局響應復位命令（General Call）來重置SCCK33112H6A 以清除 ALERT 引腳狀態，此操作還會復位 SCCK33112H6A 中的其他內部寄存器，使芯片返回到比較模式（TM=0）。表 4 給出了 F1/F0 位具體配置情況。

配置寄存器中的極性位（POL）允許用戶調整 ALERT 引腳輸出的極性。如果將 POL 位寫為0（默認值），ALERT引腳被激活時為低電平。若將 POL 位配置為 1，ALERT 引腳被激活時為高電平。上述各情況如圖4 所示。

三 組件的使用

1 Gitee鏈接地址

Demo位于amaziot_bloom_os_sdksample3rd1.1_SCCK33112H6A

Gitee源碼地址：https://gitee.com/ning./hongdou

Github源碼地址：https://github.com/ayumid/hongdou

編譯指令：.build.bat -l .amaziot_bloom_os_sdksample3rd1.1_SCCK33112H6A

2 組件功能介紹

驅動溫度芯片，定時讀取芯片寄存器，計算出當前溫度，設置溫度高限，低限，當溫度觸發門限后，會產生中斷，用戶在使用時，可以根據中斷相關服務函數，進行后續的處理。

3 代碼講解

1 drv_scck33112h6a_i2c_init

功能：該函數用于，將發送數據長度寫入scck33112h6a寄存器。

參數：五

返回值：無

示例：

//初始化i2c總線
ret = drv_scck33112h6a_i2c_init();

2 drv_scck33112h6a_i2c_read

功能：該函數用于，讀取I2C從機。

參數：五

返回值：無

示例：

RegAddr       = 0x00;
ret = drv_scck33112h6a_i2c_read(&RegAddr, &RegReadValue0);
sample_scck33112h6a_catstudio_printf("read reg 00 i2c value=0x%x, ret=%dn", RegReadValue0, ret);

3 drv_scck33112h6a_i2c_write

功能：該函數用于，發送數據到I2C從機。

參數：五

返回值：無

示例：

RegAddr       = 0x06;
RegWriteValue = 0xFF;
ret = drv_scck33112h6a_i2c_write(&RegAddr, &RegReadValue0);
sample_scck33112h6a_catstudio_printf("write i2c value=0x%x, ret=%dn", RegWriteValue, ret);

4 Demo實戰

4.1 創建一個Demo

復制20.1_file_xtu示例工程，到同一個文件夾下，修改文件名為3.1_SSD1315，如圖：

4.2 修改makefile

增加文件組件所在目錄頭文件路徑，和源文件路徑，如圖：

4.3 增加頭文件

使用代碼編輯器，將新建的工程文件加入代碼編輯器中，打開main.c，修改main.c，加入am.h等頭文件，如圖：

4.4 修改代碼

在Phase2Inits_exit 創建一個任務，如圖：

4.5 宏定義介紹

sample_scck33112h6a_uart_printf

輸出日志到DEBUG 串口，日志比較少，可以輸出到這個串口，如果日志比較多，需要輸出到usb口，以免不必要的問題出現

sample_scck33112h6a_catstudio_printf

輸出日志到USB 串口，使用catstudio查看，catstudio查看日志需要更新對應版本mdb.txt文件，軟件打開filtter過濾日志，只查看用戶輸出的日志

SAMPLE_SSCK33112H6A_STACK_SIZE

棧空間宏定義

4.6 全局變量介紹

sample_scck33112h6a_int_detect_stack_ptr

任務?？臻g，本例使用數組實現，用戶在做項目時，可以預先估算下當先任務需要的大致?？臻g，OS沒有提供可以查看?？臻g使用情況的API

sample_scck33112h6a_int_detect_task_ref

任務指針

4.7 函數介紹

Phase1Inits_enter

底層初始化，本例空

Phase1Inits_exit

底層初始化，本例空

Phase2Inits_enter

底層初始化，本例空

Phase2Inits_exit

創建主任務，初始化消息隊列，定時器，任務等。

代碼片段：

int ret = 0;
GPIOConfiguration config = {0};

//創建定時器
OSATimerCreate(&sample_scck33112h6a_int_detect_timer_ref);
//創建中斷事件
OSAFlagCreate( &sample_scck33112h6a_int_detect_flg_ref);  
Os_Create_HISR(&sample_scck33112h6a_int_detect_hisr, "sample_scck33112h6a_int_detect_hisr", sample_scck33112h6a_detect_handler, 2);
//創建中斷處理任務
OSATaskCreate(&sample_scck33112h6a_int_detect_task_ref, sample_scck33112h6a_int_detect_stack_ptr, SAMPLE_SSCK33112H6A_STACK_SIZE, 100, "detect_task", sample_scck33112h6a_detect_task, NULL);
//創建中斷處理任務
OSATaskCreate(&sample_scck33112h6a_read_task_ref, sample_scck33112h6a_read_stack_ptr, SAMPLE_SSCK33112H6A_STACK_SIZE, 100, "read_task", sample_scck33112h6a_read_task, NULL);

//初始化int引腳，這里使用70腳 gpio126
config.pinDir = GPIO_IN_PIN;
config.pinEd = GPIO_TWO_EDGE;
config.pinPull = GPIO_PULLUP_ENABLE;
config.isr = sample_scck33112h6a_irq_handler;
GpioInitConfiguration(SAMPLE_GPIO_ISR_PIN_NUM, config);

sample_scck33112h6a_read_task

主任務，獲取讀溫度信息等參數信息。

代碼片段：

void sample_scck33112h6a_read_task(void *param)
{
    GPIO_ReturnCode ret = 0;
    UINT32 value = 0;
    OSA_STATUS status = OS_SUCCESS;
    UINT32 flag_value = 0;
    unsigned char RegAddr = 0;
    UINT8 pR1_Data[2] = {0};
    UINT16 reg0 = 0;
    UINT16 reg1 = 0;
    UINT16 reg2 = 0;
    UINT16 reg3 = 0;
    
    //初始化i2c總線
    ret = drv_scck33112h6a_i2c_init();
    sample_scck33112h6a_catstudio_printf("ql_i2c_init ret %d", ret);
    //等1s
    OSATaskSleep(1 * 200);

    //寫配置寄存器
    RegAddr = DRV_SCCK33112H6A_REGISTER1_ADDRESS;
    pR1_Data[0] = 0x60;
    pR1_Data[1] = 0x90;
    ql_i2c_write_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
    RegAddr = DRV_SCCK33112H6A_REGISTER3_ADDRESS;
    //寫溫度高限寄存器
    pR1_Data[0] = 0x11;
    pR1_Data[1] = 0x00;
    ql_i2c_write_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
    //寫溫度低限寄存器
     RegAddr = DRV_SCCK33112H6A_REGISTER2_ADDRESS;
    pR1_Data[0] = 0x0A;
    pR1_Data[1] = 0x00;
    ql_i2c_write_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
    //讀配置寄存器
    RegAddr = DRV_SCCK33112H6A_REGISTER1_ADDRESS;
    ql_i2c_read_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
    reg1 = (UINT16)(pR1_Data[0] > 4;
    sample_scck33112h6a_catstudio_printf("reg3 value=0x%x, ret=%dn", reg3, ret);
    //讀溫度低限寄存器
    RegAddr = DRV_SCCK33112H6A_REGISTER2_ADDRESS;
    ql_i2c_read_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
    reg3 = (UINT16)(pR1_Data[0] > 4;
    sample_scck33112h6a_catstudio_printf("reg2 value=0x%x, ret=%dn", reg3, ret);
    
    //等1s
    OSATaskSleep(1 * 200);

    while(1)
    {
        RegAddr = DRV_SCCK33112H6A_REGISTER0_ADDRESS;
        ql_i2c_read_ext(DRV_SCCK33112H6A_I2C_NUM, DRV_SCCK33112H6A_I2C_SLAVE_ADDR, &RegAddr , 1, pR1_Data, 2);
        float temp = 0.0;
        int data = 0;
        data = (pR1_Data[0] > 4;
        //判斷如果是負數，需要按照二進制補碼，去掉符號位，減一取反后取低12位，再乘0.0625，再用0減變?yōu)樨摂?shù)
        if((data & DRV_SCCK33112H6A_TEMP_SIGNED) == DRV_SCCK33112H6A_TEMP_SIGNED)
        {
            temp = (float)(0 - (~((data & DRV_SCCK33112H6A_TEMP_MSK) - 1) & DRV_SCCK33112H6A_TEMP_MSK) * DRV_SCCK33112H6A_TEMP_1LSB);
        }
        //正數直接乘0.0625
        else
        {
            temp = (float)data * DRV_SCCK33112H6A_TEMP_1LSB;
        }
        sample_scck33112h6a_catstudio_printf("data: 0x%X data: %d temp:%fn", data, data, temp);
        sample_scck33112h6a_catstudio_printf("temprature:%fn", temp);
        //等1s
        OSATaskSleep(1 * 200);
    }
}

4.8 編譯

在SDK根目錄打開命令行，輸入命令.build.bat -l .amaziot_bloom_os_sdksample3rd1.1_SCCK33112H6A

PS F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF
λ .build.bat -l .amaziot_bloom_os_sdksample3rd1.1_SCCK33112H6A
子目錄或文件 outbin 已經存在。
命令語法不正確。
子目錄或文件 buildobj 已經存在。
gnumake: Entering directory `F:/3.asr-b/cat.1-asr1606/1.software/BlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF/amaziot_bloom_os_sdk/sample/3rd/1.1_SCCK33112H6A'
armcc.exe -c  --cpu Cortex-R4 --no_unaligned_access -g -O2 --apcs /inter --diag_suppress 2084,1,2,177,188,223,550,1296,2795,6319,9931,9933 --diag_error=warning --gnu --thumb --loose_implicit_cast  -DDATA_COLLECTOR_IMPL -DISPT_OVER_SSP -DDIAG_SSP_DOUBLE_BUFFER_USE_DYNAMIC_ALLOCATION -DENV_XSCALE -DL1_DCXO_ENABLED -DLTE_HIGH_MOBILITY_OPTIMIZATION -DRUN_XIP_MODE -DCRANE_Z2 -DCA_LONG_IPC_MSG -DNEZHA3 -DNEZHA3_1826 -DUPGRADE_PLMS -DUPGRADE_PLMS_SR -DLTE_GSMMULTIBCCH -DGPLC_LTE_RSSI_SCAN -DL1V_NEW_RSSI -DUPGRADE_PLMS_3G -DUPGRADE_PLMS_L1 -DUPGRADE_FG_PLMS -DFG_PLMS_URR -DUPGRADE_L1A_FG_PLMS -DUPGRADE_PLMS_STAGE_2 -DUPGRADE_MBCCH -DMULTI_BCCH_READY_IND -DURR_MRAT_ICS_SEARCH -DUPGRADE_ICS -DMRAT_NAS -DUPGRADE_PLMS_SEARCH_API -DICS_MBCCH -DICS_MBCCH_2G_RSSI -DDIAG_NEWPP -DPHS_SW_DEMO -DPHS_SW_DEMO_TTC -DPHS_SW_DEMO_TTC_PM -DFULL_SYSTEM -D_DDR_INIT_ -D_TAVOR_HARBELL_ -DUPGRADE_ARBEL_PLATFORM -D_TAVOR_B0_SILICON_ -DTDL1C_SPY_ENABLE -DDLM_TAVOR -DTAVOR -DFLAVOR_DUALCORE -DDEBUG_D2_MOR_REG_RESEREVED_ENABLE -D_DIAG_USE_COMMSTACK_ -D_TAVOR_DIAG_ -DPM_DEBUG_MODE_ENABLED -DPM_D2FULL_MODE -DPM_EXT_DBG_INT_ARR -DFEATURE_WB_AMR_PS -DMACRO_FOR_LWG -DHL_LWG -DOPTIMIZE_FOR_2G_BCCH -DPLAT_TEST -D_FDI_USE_OSA_ -DPLAT_USE_THREADX -DLWIP_IPNETBUF_SUPPORT -DCRANE_MCU_DONGLE -DAT_OVER_UART -DPHS_SW_DEMO_TTC_PM -DUPGRADE_LTE_ONLY -DEXT_AT_MODEM_SUPPORT -DLTEONLY_THIN_SINGLE_SIM -DLFS_FILE_SYS -DLFS_FILE_SYS_V2 -DPSM_ENABLE -DNO_PAHO_MQTT -DNO_XML -DNO_LWM2M -DREMOVE_MBEDTLS -DNO_AT_NET -DCRANE_SD_NOT_SUPPORT -DNTP -DYMODEM_EEH_DUMP -DENABLE_DM_LTEONLY -DLTEONLY_THIN -DNO_EXTEND_MY_Q_AT -DNOT_SUPPORT_HTTPS -DNOT_SUPPORT_PM813 -DCRANEL_4MRAM -DREMOVE_PB -DUART_NEW_VERSION -DREMOVE_MEP -DREMOVE_SMS -DREMOVE_ENVSIM -DAPN_INCODE -DLTEONLY_THIN_SINGLE_SIM_2MFLASH -DASR160X_OPENCPU_FEATURE -DENABLE_UART3_FEATRUE -DENABLE_UART4_FEATRUE -DYUGE_MBEDTLS_3_2_1 -DENABLE_MAC_TX_DATA_LOGGING -DDISABLE_NVRAM_ACCESS -DINTEL_UPGRADE_EE_HANDLER_SUPPORT -DLTE_W_PS -DL1_DUAL_MODE -DUPGRADE_HERMON_DUAL -DINTEL_UPGRADE_DUAL_RAT -DINTEL_UPGRADE_GPRS_CIPHER_FLUSH -DUPGRADE_ENHANCED_QUAD_BAND -DINTEL_2CHIP_PLAT -DI_2CHIP_PLAT -DUPGRDE_TAVOR_COMMUNICATION -DRUN_WIRELESS_MODEM -DFLAVOR_DDR12MB_GB1MB5 -DFEATURE_SHMEM -DACIPC_ENABLE_NEW_CALLBACK_MECHANISM -DRELIABLE_DATA -DMAP_NSS -DTV_FNAME=""SW_PLATFORM=PMD2NONE PHS_SW_DEMO PHS_SW_DEMO_PM SRCNUCLEUS FULL_SYSTEM NOACRTC PDFLT PLAT_TEST PV2 DIAGOSHMEM NVM WITHL1V"" -DTV_FDESC=""SW_DESCRIPTION="" -DENABLE_ACIPC -D_DATAOMSL_ENABLED_ -DUSB_CABLE_DETECTION_VIA_PMIC -DMIPS_TEST -DMIPS_TEST_RAM -DFLAVOR_DIET_RAM -DNVM_INCLUDE -DMSL_INCLUDE -DMSL_POOL_MEM -DNO_AUDIO -DOSA_QUEUE_NAMES -D_DIAG_DISABLE_USB_ -DOSA_NUCLEUS -DOSA_USED -DPM_D2NONE_MODE -DCRANE_SOC_TEMPERATURE_SENSOR -DL1_SW_UPDATE_FOR_DIGRF -DPHS_L1_SW_UPDATE_R7 -DUPGRADE_LTE -DFRBD_CALIB_NVM -DFRBD_AGC_CALIB -DFRBD_FDT_CALIB -DHSPA_MPR -DCAPT_PARAMS_OPTIMIZE -DL1_WB_R99_ONLY -DL1V_WB_R99_ONLY -DINTERGRATED_RF_SUPPORT -DL1_RX_DIV_SUPPORT -DENABLE_OOS_HANDLING -DTAVOR_D2_WB_L1_SUPPORT -DL1_DDR_HIGH_FREQ -DUPGRADE_DIGRF3G_SUPPORT -DW_PS_PLUS_G_PAGING -D"NO_APLP=0" -DINTEL_UPGRADE_UNIFIED_VOICE_TASK -DINTEL_UPGRADE_R99 -DAPLP_SPY_ENABLE -D__TARGET_FEATURE_DOUBLEWORD -DWHOLE_UMTS_STACK -DUSE_TTPCOM_CSR_BLUETOOTH_AUDIO_GAIN_CONTROL -DL1_UPGRADE_R5 -DUPGRADE_EDGE -DUPGRADE_R4_FS1 -DINTEL_UPGRADE_GSM_CRL_IF -DUPGRADE_EGPRS_M -DINTEL_UPGRADE_EGPRS_M -DINTEL_UPGRADE_RF_PARAMS_IN_CF_TDS -DINTEL_UPGRADE_2SAMPLES_PER_SYMBOL -D"GPRS_MULTISLOT_CLASS=12" -D"EGPRS_MULTISLOT_CLASS=12" -DMARVELL_UPGRADE_BSIC_REDESIGN -DMSL_INCLUDE -DINTEL_HERMON_SAC -DCRANE_CUST_BUILD -DL1_SW_UPDATE_FOR_DIGRF -DFLAVOR_COM -DSILICON_PV2 -DSILICON_SEAGULL -DSILICON_TTC_CORE_SEAGULL -DPCAC_INCLUDE -Otime  -DBUILD_DATE=""06 21 2024"" -DBUILD_TIME=""10:56:09"" -Iatcmdsinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonyyugeinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalUARTinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalcoreinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalPMUinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalGPIOinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xosposixinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xdiagdiag_logicsrc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xcswSysCfginc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xcswplatforminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xenvwin32inc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xcswBSPinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xcswplatformdev_platbuild -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xososainc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xosthreadxinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xosnu_xscaleinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacpsminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcachttpclientsrc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xdiagdiag_logicinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptimerinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopintcinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xcswPMinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoppminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilTickManagerinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopBSPinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonyatcmdsrvinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonyatparserinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonysdkinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcachttpclientinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacciinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcinclude -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcincludearch -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcincludeipv4 -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcincludeipv6 -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcincludelwip -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcaclwipv4v6srcincludenetif -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopmmi_matinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xtavorArbelinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xtavorenvinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonymodeminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacdusterinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacfotainc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalI2Cinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalACIPCinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilfatsysflash -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilFDIsrcINCLUDE -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalMMUinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilFDIsrcFDI_ADD -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilFDIsrcFM_INC -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilfatsysfshdr -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutillittlefsinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacttsinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacdialinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilcsw_memoryinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoputilitiesinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopcommpminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilnvminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilEEhandlerinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilEEhandlersrc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopRTCinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhoptelephonyci_clientinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalBT_deviceinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalUARTinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopmrdinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopdmainc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilsoftutilinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhalSPIinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacwebsocketinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacatnet_srvinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xsoftutilfotacomminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xaud_swAudioinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xaud_swACM_COMMinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xaud_swaudio_stubsrc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhopaaminc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xaud_swAudioHALinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xhaldbgshellinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFincludeasr160xpcacopencpuinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFamaziot_bloom_os_sdkutils -IF:/3.asr-b/cat.1-asr1606/1.software/BlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF/amaziot_bloom_os_sdk/sample/3rd/1.1_SCCK33112H6Aaminc -IF:/3.asr-b/cat.1-asr1606/1.software/BlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF/amaziot_bloom_os_sdk/sample/3rd/1.1_SCCK33112H6Aatcmdsinc -IF:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFamaziot_bloom_os_sdk3rd_drivesSCCK33112H6A  -o buildobj/ext_at_cmds.o F:/3.asr-b/cat.1-asr1606/1.software/BlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF/amaziot_bloom_os_sdk/sample/3rd/1.1_SCCK33112H6A/atcmds/src/ext_at_cmds.c
armlink.exe buildobj/main.o buildobj/ext_at_cmds.o buildobj/ext_at_controller.o buildobj/drv_scck33112h6a.o 
                -o F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFoutbinArbel_PMD2NONE_40M.axf 
                --via F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFprebuilt_1606lArbel_PMD2NONE_targ_objliblist.txt 
                --elf 
                --scatter F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFprebuilt_1606lCrane_DS_4M_Ram_2M_Flash_XIP_CIPSRAM_Common_SingleSIM.sct 
                --predefine="-DLTEONLY_THIN_SINGLE_SIM" --map --symbols --info sizes,totals 
                --list F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFoutbinArbel_PMD2NONE_40M.map 
                --keep init.o(Header) --keep init.o(Vectors) --diag_suppress 6312,6314,6319,6329 
                --feedback F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFoutfeedbackLinkOptLteonlyThin_SingleSim_NoSMS.txt
F:3.asr-bcat.1-asr16061.softwareBlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRFtoolsbuildimage_1606l.bat
SDK_PROD_TYPE   : [DM]
SDK_CUST_SKU    : [THIN_SINGLE_SIM_NO_SMS]
SDK_PS_MODE     : [LTEONLY]
SDK_CHIP_VER    : [Z2A0]
SDK_OS_TYPE     : [TX]
Platform Convertion Tools v4.01 with PS option extension
Convertion done!
|INPUT   |outbincp_1606L.bin
|MARK    |NAME    |EXEADDR .LOADADDR.LENGTH  .CPZLADDR|COMPRESS STASTIC              |
|--------|--------|--------.--------.--------.--------|------------------------------|
|This Is LteOnly 4M|
|RW_CPZ_1|DDR_RW_ |7e119000.80064ea8.0000ce04.80065000|0000ce04->00003000
|This Is LteOnly 4M|
|RW_CPZ_2|PS_NCAH |7e388000.80071cac.00001300.80068000|00001300->00001000
|This Is LteOnly 4M|
|RW_CPZ_3|ITCM    |7e3dac00.80072fac.0000f51c.80069000|0000f51c->0000a000
|This Is LteOnly 4M|
|RW_CPZ_4|CODE_PS |7e1aa000.800824c8.0002fe38.80073000|0002fe38->0001e000
|This Is LteOnly 4M|
|RW_CPZ_5|CODEPSB |7e1dc000.800b2300.000339c0.80091000|000339c0->0001b000
|This Is LteOnly 4M|
|RW_CPZ_6|CODEPSC |7e213000.800e5cc0.000323ec.800ac000|000323ec->0001b000
|This Is LteOnly 4M|
|RW_CPZ_7|CODEPSD |7e249000.801180ac.00028d88.800c7000|00028d88->0001a000
|This Is LteOnly 4M|
|RW_CPZ_8|CODEPSE |7e277000.80140e34.0002e310.800e1000|0002e310->0001a000
|This Is LteOnly 4M|
|RW_CPZ_9|CODEPSF |7e2a9000.8016f144.0001c948.800fb000|0001c948->00011000
|This Is LteOnly 4M|
|RW_CPZ_A|CODE_PL |7e2ca000.8018ba8c.0002fa44.8010c000|0002fa44->0001e000
|This Is LteOnly 4M|
|RW_CPZ_B|CODEPLB |7e2fa000.801bb4d0.00039058.8012a000|00039058->00021000
|This Is LteOnly 4M|
|RW_CPZ_C|CODEPLC |7e337000.801f4528.000268d4.8014b000|000268d4->00011000
|--------|--------|--------.--------.--------.--------|------------------------------|
|                                                     |      0x00203dfc -> 0x00145000|
|                                                     |       2.015(MB) ->  1.270(MB)|
|------------------------------------------------------------------------------------|
cp_1606L.axf
cp_1606L.bin
cp_1606L.map
gnumake: Leaving directory `F:/3.asr-b/cat.1-asr1606/1.software/BlOOM_OS_1606_OPENCPU_1191_A09_WIHT_NEWRF/amaziot_bloom_os_sdk/sample/3rd/1.1_SCCK33112H6A'
"copy NEZHAC_CP_CNR_MIFI_TX.bin to ./ "

已復制         1 個文件。

4.9 生成固件

參考入門中開發工具，生成工具。

4.10 測試

測試步驟：

參考編譯教程，和文檔開頭的編譯指令，進行編譯

按照編譯教程選擇對應的選項

燒錄

4.11 固件

上電后，串口助手會打印出當前獲取到的溫度，以及芯片寄存器原始信息；

點擊下載 SCCK33112H6A Demo 固件

5 生態組件鏈接

數字溫度傳感器（芯片）（詳情請見奇跡物聯知識庫）

本文章源自奇跡物聯開源的物聯網應用知識庫Cellular IoT Wiki，更多技術干貨歡迎關注收藏Wiki：Cellular IoT Wiki 知識庫（https://rckrv97mzx.feishu.cn/wiki/wikcnBvAC9WOkEYG5CLqGwm6PHf）

歡迎同學們走進AmazIOT知識庫的世界！

這里是為物聯網人構建的技術應用百科，以便幫助你更快更簡單的開發物聯網產品。

Cellular IoT Wiki初心：

在我們長期投身于蜂窩物聯網 ODM/OEM 解決方案的實踐過程中，一直被物聯網技術碎片化與產業資源碎片化的問題所困擾。從產品定義、芯片選型，到軟硬件研發和測試，物聯網技術的碎片化以及產業資源的碎片化，始終對團隊的產品開發交付質量和效率形成制約。為了減少因物聯網碎片化而帶來的重復開發工作，我們著手對物聯網開發中高頻應用的技術知識進行沉淀管理，并基于 Bloom OS 搭建了不同平臺的 RTOS 應用生態。后來我們發現，很多物聯網產品開發團隊都面臨著相似的困擾，于是，我們決定向全體物聯網行業開發者開放奇跡物聯內部沉淀的應用技術知識庫 Wiki，期望能為更多物聯網產品開發者減輕一些重復造輪子的負擔。

Cellular IoT Wiki沉淀的技術內容方向如下：

奇跡物聯的業務服務范圍：基于自研的NB-IoT、Cat1、Cat4等物聯網模組，為客戶物聯網ODM/OEM解決方案服務。我們的研發技術中心在石家莊，PCBA生產基地分布在深圳、石家莊、北京三個工廠，滿足不同區域&不同量產規模&不同產品開發階段的生產制造任務。跟傳統PCBA工廠最大的區別是我們只服務物聯網行業客戶。

連接我們，和10000+物聯網開發者一起 降低技術和成本門檻

讓蜂窩物聯網應用更簡單~~

哈哈你終于滑到最重要的模塊了，

千萬不！要！劃！走！忍住沖動！~

歡迎加入飛書“開源技術交流群”，隨時找到我們哦~

點擊鏈接如何加入奇跡物聯技術話題群（https://rckrv97mzx.feishu.cn/docx/Xskpd1cFQo7hu9x5EuicbsjTnTf）可以獲取加入技術話題群攻略

Hey 物聯網從業者，

你是否有了解過奇跡物聯的官方公眾號“eSIM物聯工場”呢？

這里是奇跡物聯的物聯網應用技術開源wiki主陣地，歡迎關注公眾號，不迷路～

及時獲得最新物聯網應用技術沉淀發布

審核編輯 黃宇