Arduino UNO液晶屏開源

2077297 2022-08-12 | zip | 0.01 MB | 次下載 | 2積分

資料介紹

電路板圖如下：

成分

ARDUINO UNO REV3	× 1
通用 220 歐姆電阻器	× 1
LCM-S01602DSF/A Lumex 光電/組件公司	× 1

描述

Arduino UNO 液晶屏

建造盾牌：

組裝：

盾構圖如下：

LCD RS 引腳到數字引腳 12

LCD 使能引腳到數字引腳 11

LCD D4 引腳到數字引腳 5

LCD D5 引腳到數字引腳 4

LCD D6 引腳到數字引腳 3

LCD D7 引腳到數字引腳 2

LCD R/W 引腳到 GND

LCD VSS 引腳至 GND

LCD VCC 引腳至 5V

LCD LED+ 通過 220 歐姆電阻器至 5V

LCD LED- 到 GND

電阻器進入電阻器符號。每個孔中都有焊針。就是這樣！

使用盾牌：

要使用顯示器，您必須在 Arduino IDE 上安裝 LiquidCrystalDisplay 庫。

我將在下面留下一個 Hello world 示例來使用顯示器。;)

代碼

你好世界！

阿杜諾

?	/*
?	LiquidCrystal Library - Hello World
?	?
?	Demonstrates the use a 16x2 LCD display.The LiquidCrystal
?	library works with all LCD displays that are compatible with the
?	Hitachi HD44780 driver. There are many of them out there, and you
?	can usually tell them by the 16-pin interface.
?	?
?	This sketch prints "Hello World!" to the LCD
?	and shows the time.
?	?
?	The circuit:
?	* LCD RS pin to digital pin 12
?	* LCD Enable pin to digital pin 11
?	* LCD D4 pin to digital pin 5
?	* LCD D5 pin to digital pin 4
?	* LCD D6 pin to digital pin 3
?	* LCD D7 pin to digital pin 2
?	* LCD R/W pin to ground
?	* LCD VSS pin to ground
?	* LCD VCC pin to 5V
?	* 10K resistor:
?	* ends to +5V and ground
?	* wiper to LCD VO pin (pin 3)
?	?
?	Library originally added 18 Apr 2008
?	by David A. Mellis
?	library modified 5 Jul 2009
?	by Limor Fried (http://www.ladyada.net)
?	example added 9 Jul 2009
?	by Tom Igoe
?	modified 22 Nov 2010
?	by Tom Igoe
?	modified 7 Nov 2016
?	by Arturo Guadalupi
?	?
?	This example code is in the public domain.
?	?
?	http://www.arduino.cc/en/Tutorial/LiquidCrystalHelloWorld
?	?
?	*/
?	?
?	// include the library code:
?	#include
?	?
?	// initialize the library by associating any needed LCD interface pin
?	// with the arduino pin number it is connected to
?	const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2;
?	LiquidCrystal lcd(rs, en, d4, d5, d6, d7);
?	?
?	void setup() {
?	// set up the LCD's number of columns and rows:
?	lcd.begin(16, 2);
?	// Print a message to the LCD.
?	lcd.print("hello, world!");
?	}
?	?
?	void loop() {
?	// set the cursor to column 0, line 1
?	// (note: line 1 is the second row, since counting begins with 0):
?	lcd.setCursor(0, 1);
?	// print the number of seconds since reset:
?	lcd.print(millis() / 1000);
?	}