資料介紹

Table of Contents
CN0229 Evaluation Board Guide
Overview
CN0229 is a multichannel, flexible, analog output solution with only two analog components and meets most requirements for multichannel I/O cards, programmable logic controllers (PLCs), and distributed control systems (DCSs) applications. The circuit also contains key features for industrial applications, such as on-chip output fault detection, packet error checking (PEC) by the CRC, flexible power-up options, and ESD protection making it an ideal choice for robust industrial control systems.
The AD5750-2 is a single-channel, low cost, precision voltage/current output driver developed to meet the requirements of industrial process control applications. The voltage output range can be programmed for the standard output ranges for PLC and DCS applications: 0 V to 5 V, 0 V to 10 V, ?5 V to +5 V, and ?10 V to +10 V with a 20% overrange setting provided for the standard ranges. The current output, which is provided on a separate pin, can be programmed for the ranges of 4 mA to 20 mA, 0 mA to 20 mA, ?20 mA to +20 mA, 0 mA to 24 mA, and ?24 mA to +24 mA. The unipolar ranges have a 2% overrange setting.
The AD5686R is a quad 16-bit nanoDAC+ with rail-to-rail voltage-buffered outputs integrated with an on-chip 2 ppm/°C typical (5 ppm/°C maximum), 2.5 V reference. The on-chip reference can drive the reference input of all four AD5750-2s, has a low output impedance of 0.05 Ω, and can source and sink up to 5 mA.
The ADuM1301 is a triple-channel digital isolator. The ADuM5400 is a quad-channel digital isolator with an integrated, isolated, dc-to-dc converter. They are both based on iCoupler? technology and are used to provide isolation between the signal chain and the system microcontroller, with an isolation rating of 2.5 kV rms. The ADuM5400 provides an isolated 5 V power supply for the 5 V circuits in the secondary side.
The EVAL-CN0229-SDPZ board connects to ADI’s System Demonstration Platform (SDP) and is powered by a triple output DC power supply of +15 V, -15 V and 6 V.
Required Equipment
- EVAL-SDP-CB1Z Controller Board (SDP-B Board)
- Triple Output DC Power Supply (6 V, +15 V and -15 V)
- Agilent E3631A 0 V to 6 V/5 A; ±25 V/1 A Triple Output DC Power Supply
- Digital Multimeter for Verification (Optional)
- Agilent 34401A 6.5 Digital Multimeter
- PC with the following Minimum Requirements
- Windows 7 or higher
- USB interface
General Setup
Block assignments
- The EVAL-CN0229-SDPZ (CN-0229 Board) connects to the EVAL-SDP-CB1Z (SDP-B Board) via the 120-Pin connector
- The EVAL-SDP-CB1Z (SDP-B Board) connects to the PC via the USB cable.
- Terminal block CN1 is the +/- 15 V power supply input
- Terminal block CN2 is the +6 V power supply input
- Four OUT_[x] voltage/current output channels
Do not connect the USB cable to the Mini-USB connector on the SDP board before turning on the dc power supply for the EVAL-CN0229-SDPZ.
Jumper settings
See image below for jumper settings. The bolded values are the default settings for the EVAL-CN0229-SPDZ.
Installing the Evaluation Software
- Extract the file CN0229_Evaluation_Software.zip and open the file setup.exe.
NOTE: It is recommended that you install the CN0229 Evaluation Software to the default directory path C:/Program Files (x86)/Analog Devices/CN0229/ and all National Instruments products to C:/Program Files/National Instruments/
- Click Next to view the installation review page
- Click Next to start the installation
- Upon completion of the installation of the CN-0229 Evaluation Software, the installer for the ADI SDP Drivers will execute.
NOTE: It is recommended that you close all other applications before clicking “Next”. This will make it possible to update relevant system files without having to reboot your computer.
- Press “Next” to set the installation location for the SDP Drivers.
It is recommended that you install the drivers to the default directory path
C:/Program Files/Analog Devices/SDP/Drivers
- Press “Next” to install the SDP Drivers and complete the installation of all software. Click “Finish” when done.
Using the Evaluation Software
Main Tab
- Connection (Highlighted Dark Blue)
- Connect Button
- Starts the connection with the CN0229 Evaluation Board
- Disconnect Button
- Ends the connection with the CN0229 Evaluation Board
- System Configuration (Highlighted Red)
- Connector
- Selects which 120-pin connection of the SDP-B Board to use
- SLCK
- Sets the SPI clock frequency used by the evaluation board
- Set/Reset (Highlighted Light Blue and Pink)
- Reset
- Resets AD5686R
- Set All
- Sets all channels to their corresponding settings
- Quit
- Exit the application
- Channel 1 Settings (Highlighted Violet)
- Output
- Enables or disables Channel 1
- Range
- Sets the voltage/current output range of Channel 1
- Value
- Sets the hex value corresponding to the desired output level in Channel 1
- Channel 2 Settings (Highlighted Green)
- Output
- Enables or disables Channel 2
- Range
- Sets the voltage/current output range of Channel 2
- Value
- Sets the hex value corresponding to the desired output level in Channel 2
- Channel 3 Settings (Highlighted Orange)
- Output
- Enables or disables Channel 3
- Range
- Sets the voltage/current output range of Channel 3
- Value
- Sets the hex value corresponding to the desired output level in Channel 3
- Channel 4 Settings (Highlighted Yellow)
- Output
- Enables or disables Channel 4
- Range
- Sets the voltage/current output range of Channel 4
- Value
- Sets the hex value corresponding to the desired output level in Channel 4
Running the System
- Open the CN0229.exe application from the default installation location.
- Set the correct connector and SCLK settings for the board in the System Configuration section.
- Click the Connect Button
- Upon successful connection, select the desired channel to be used.
- Set the output of the channel to enable.
- Select the range of desired output.
- Input a corresponding hex value of the output level and select Set CH[x].
- In case all channels are to be used, set all desired settings for each channel and click the Set ALL button.
- Click Disconnect Button if finished.
More Information and Useful Links
Schematic, PCB Layout, Bill of Materials
EVAL-CN0229-SDPZ Design & Integration Files
- Schematics
- PCB Layout
- Bill of Materials
- PADS project
End of Document
声明:本文内容及配图由入驻作者撰写或者入驻合作网站授权转载。文章观点仅代表作者本人,不代表电子发烧友网立场。文章及其配图仅供工程师学习之用,如有内容侵权或者其他违规问题,请联系本站处理。 举报投诉
- CN0335软件用户指南5次下载
- CN0336软件用户指南17次下载
- CN0349软件用户指南6次下载
- CN0350软件用户指南7次下载
- CN-0354软件用户指南6次下载
- CN0355软件用户指南9次下载
- CN0196软件用户指南9次下载
- CN0203软件用户指南6次下载
- CN0218软件用户指南8次下载
- CN0235软件用户指南4次下载
- CN0276软件用户指南5次下载
- CN-0288软件用户指南8次下载
- CN-0301软件用户指南11次下载
- CN-0326软件用户指南10次下载
- CN0229 设计与集成文件0次下载
- H桥电机驱动器CN8042广泛应用于汽车电子、工业自动化60次阅读
- 上位机软件的用户界面设计技巧1693次阅读
- 国产电路仿真软件哪个好7388次阅读
- 搞不懂组态软件和HMI?常见组态软件有哪些?7009次阅读
- 常用的远程控制软件介绍2588次阅读
- VisionFive2开发板开箱体验和Debian新手指南1910次阅读
- 医疗器械软件风险分析介绍 医疗设备软件静态和动态分析技巧2352次阅读
- 如何使用openEuler用户软件仓(EUR)1514次阅读
- 基于STM32 MCU应用的EMC指南之软件篇1256次阅读
- 开源、可重用的软件堆栈支持CbM的实时处理和算法开发1185次阅读
- EsDA为用户带来简单易用的软件设计体验2120次阅读
- 使用含快速开关SiC器件的RC缓冲电路实用解决方案和指南2927次阅读
- 常见的组态软件有哪些12948次阅读
- 一款以BitTorrent代币连接和奖励用户的软件BitTorrent Speed介绍3402次阅读
- 组态软件是什么_组态软件有什么用36085次阅读
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論