電子發燒友App
創作
發文章
發帖 
提問 
發資料
發視頻資料介紹
Table of Contents
AD7980 - No-OS Driver for Renesas Microcontroller Platforms
Supported Devices
Evaluation Boards
Overview
The AD7980 is a 16-bit, successive approximation, analog-to-digital converter (ADC) that operates from a single power supply, VDD. It contains a low power, high speed, 16-bit sampling ADC and a versatile serial interface port. On the CNV rising edge, it samples an analog input IN+ between 0 V to REF with respect to a ground sense IN?. The reference voltage, REF, is applied externally and can be set independent of the supply voltage, VDD. Its power scales linearly with throughput.
The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single, 3-wire bus and provides an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate supply VIO.
The AD7980 is housed in a 10-lead MSOP or a 10-lead QFN (LFCSP) with operation specified from ?40°C to +125°C.
The AD7980-EP supports defense and aerospace applications (AQEC)
Applications
- Battery-powered equipment
- Communications
- ATE
- Data acquisitions
- Medical instruments
The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for different microcontroller platforms.
Driver Description
The driver contains two parts:
- The driver for the AD7980 part, which may be used, without modifications, with any microcontroller.
- The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver.
The Communication Driver has a standard interface, so the AD7980 driver can be used exactly as it is provided.
There are three functions which are called by the AD7980 driver:
- SPI_Init() – initializes the communication peripheral.
- SPI_Write() – writes data to the device.
- SPI_Read() – reads data from the device.
SPI driver architecture
The following functions are implemented in this version of AD7980 driver:
| Function | Description |
|---|---|
| char AD7980_Init(void) | Initializes the communication peripheral. |
| unsigned short AD7980_Conversion(void) | Initiates conversion and reads data. |
| float AD7980_ConvertToVolts(unsigned short rawSample, float vRef) | Converts a 16-bit raw sample to volts. |
This version of AD7980 driver uses the CS Mode 4-Wire, without Busy Indicator mode; the device has to be connected to an SPI-compatible digital host as following:
- The AD7980 CNV signal (C2 on the oscilloscope) has to be connected to the SPI MOSI signal.
- The AD7980 SDI signal (C1 on the oscilloscope) has to be connected to the SPI CS signal (Chip Select has to be controlled manually).
- The AD7980 SCK signal (C4 on the oscilloscope) has to be connected to the SPI SCK signal.
- The AD7980 SDO signal (C3 on the oscilloscope) has to be connected to the SPI MISO signal.
Signals generated by the driver on the SPI port
Downloads
- RL78G14 Common Drivers: https://github.com/analogdevicesinc/no-OS/tree/master/Renesas/RL78G14/Common
Renesas RL78G13 Quick Start Guide
This section contains a description of the steps required to run the AD7980 demonstration project on a Renesas RL78G13 platform.
Required Hardware
Required Software
Hardware Setup
A EVAL-AD7980-PMDZ has to be connected to the PMOD1 connector, pins 1 to 6 (see image below).
- If you want to use AVDD > DVDD (= 3.3V) then JP3 on PmodAD4 must be removed. The range for AVDD is 3.0V ≤ AVDD ≤ 5.5V.
Reference Project Overview
The reference project:
- samples the input voltage;
- displays the value on the LCD (in hexa, decimal and volts).
- The reference voltage for the AD7980 is 2.5V.
- If you want to use another reference voltage, you will need to modify the vRef parameter in ‘AD7980_ConvertToVolts()’ function from ‘PmodAD4.c’. The range for VREF is 2.4V ≤ VREF ≤ 5.1V.
Software Project Tutorial
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RL78G13 for controlling and monitoring the operation of the ADI part.
- Run the IAR Embedded Workbench for Renesas RL78 integrated development environment.
- Choose to create a new project (Project – Create New Project).
- Select the RL78 tool chain, the Empty project template and click OK.
- Select a location and a name for the project (ADIEvalBoard for example) and click Save.
- Open the project’s options window (Project – Options).
- From the Target tab of the General Options category select the RL78 – R5F100LE device.
- From the Setup tab of the Debugger category select the TK driver and click OK.
- Extract the files from the lab .zip archive and copy them into the project’s folder.
- The new source files have to be included into the project. Open the Add Files… window (Project – Add Files…), select all the copied files and click open.
- At this moment, all the files are included into the project.
- The project is ready to be compiled and downloaded on the board. Press the F7 key to compile it. Press CTRL + D to download and debug the project.
- A window will appear asking to configure the emulator. Keep the default settings and press OK.
- To run the project press F5.
Renesas RL78G14 Quick Start Guide
This section contains a description of the steps required to run the AD7980 demonstration project on a Renesas RL78G14 platform using the EVAL-AD7980-PMDZ.
Required Hardware
Required Software
- The AD7980 demonstration project for the Renesas RL78G14 platform.
The AD7980 demonstration project for the Renesas RL78G14 platform consists of three parts: the AD7980 Driver, the EVAL-AD7980-PMDZ Demo for RL78G14 and the RL78G14 Common Drivers.
All three parts have to be downloaded.
Hardware Setup
A EVAL-AD7980-PMDZ has to be connected to the PMOD1 connector, pins 1 to 6 (see image below).
- If you want to use AVDD > DVDD (= 3.3V) then JP3 on PmodAD4 must be removed. The range for AVDD is 3.0V ≤ AVDD ≤ 5.5V.
The reference project:
- samples the input voltage;
- displays the value on the LCD (in hexa, decimal and volts).
- The reference voltage for the AD7980 is 2.5V.
- If you want to use another reference voltage, you will need to modify the vRef parameter in ‘AD7980_ConvertToVolts()’ function from ‘PmodAD4.c’. The range for VREF is 2.4V ≤ VREF ≤ 5.1V.
Software Project Tutorial
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RL78G14 for controlling and monitoring the operation of the ADI part.
- Run the IAR Embedded Workbench for Renesas RL78 integrated development environment.
- Choose to create a new project (Project – Create New Project).
- Select the RL78 tool chain, the Empty project template and click OK.
- Select a location and a name for the project (ADIEvalBoard for example) and click Save.
- Open the project’s options window (Project – Options).
- From the Target tab of the General Options category select the RL78 – R5F104PJ device.
- From the Setup tab of the Debugger category select the TK driver and click OK.
- Copy the downloaded files into the project's folder.
- The new source files have to be included into the project. Open the Add Files… window (Project – Add Files…), select all the copied files and click open.
- At this moment, all the files are included into the project.
- The project is ready to be compiled and downloaded on the board. Press the F7 key to compile it. Press CTRL + D to download and debug the project.
- A window will appear asking to configure the emulator. Keep the default settings and press OK.
- To run the project press F5.
Renesas RX62N Quick Start Guide
This section contains a description of the steps required to run the AD7980 demonstration project on a Renesas RX62N platform.
Required Hardware
Required Software
Hardware Setup
A EVAL-AD7980-PMDZ has to be interfaced with the Renesas Demonstration Kit (RDK) for RX62N:
PmodAD4 Pin 1 (CS) → YRDKRX62N J8 connector Pin 15 PmodAD4 Pin 2 (MOSI) → YRDKRX62N J8 connector Pin 19 PmodAD4 Pin 3 (MISO) → YRDKRX62N J8 connector Pin 22 PmodAD4 Pin 4 (CLK) → YRDKRX62N J8 connector Pin 20 PmodAD4 Pin 5 (GND) → YRDKRX62N J8 connector Pin 4 PmodAD4 Pin 6 (VCC) → YRDKRX62N J8 connector Pin 3
Reference Project Overview
The reference project initiates conversions and reads the captured data from the AD7980.
Software Project Setup
This section presents the steps for developing a software application that will run on the Renesas Demo Kit for RX62N for controlling and monitoring the operation of the ADI part.
- Run the High-performance Embedded Workshop integrated development environment.
- A window will appear asking to create or open project workspace. Choose “Create a new project workspace” option and press OK.
- From “Project Types” option select “Application”, name the Workspace and the Project “ADIEvalBoard”, select the “RX” CPU family and “Renesas RX Standard” tool chain. Press OK.
- A few windows will appear asking to configure the project:
- In the “Select Target CPU” window, select “RX600” CPU series, “RX62N” CPU Type and press Next.
- In the “Option Setting” windows keep default settings and press Next.
- In the “Setting the Content of Files to be generated” window select “None” for the “Generate main() Function” option and press Next.
- In the “Setting the Standard Library” window press “Disable all” and then Next.
- In the “Setting the Stack Area” window check the “Use User Stack” option and press Next.
- In the “Setting the Vector” window keep default settings and press Next.
- In the “Setting the Target System for Debugging” window choose “RX600 Segger J-Link” target and press Next.
- In the “Setting the Debugger Options” and “Changing the Files Name to be created” windows keep default settings, press Next and Finish.
- The workspace is created.
- The RPDL (Renesas Peripheral Driver Library) has to integrated in the project. Unzip the RPDL files (double-click on the file “RPDL_RX62N.exe”). Navigate to where the RPDL files were unpacked and double-click on the “Copy_RPDL_RX62N.bat” to start the copy process. Choose the LQFP package, type the full path where the project was created and after the files were copied, press any key to close the window.
- The new source files have to be included in the project. Use the key sequence Alt, P, A to open the “Add files to project ‘ADIEvalBoard’” window. Double click on the RPDL folder. From the “Files of type” drop-down list, select “C source file (*.C)”. Select all of the files and press Add.
- To avoid conflicts with standard project files remove the files “intprg.c” and “vecttbl.c” which are included in the project. Use the key sequence Alt, P, R to open the “Remove Project Files” window. Select the files, click on Remove and press OK.
- Next the new directory has to be included in the project. Use the key sequence Alt, B, R to open the “RX Standard Toolchain” window. Select the C/C++ tab, select “Show entries for: Include file directories” and press Add. Select “Relative to: Project directory”, type “RPDL” as sub-directory and press OK.
- The library file path has to be added in the project. Select the Link/Library tab, select “Show entries for: Library files” and press Add. Select “Relative to: Project directory”, type “RPDL/RX62N_library” as file path and press OK.
- Because the “intprg.c” file was removed the “PIntPrg” specified in option “start” has to be removed. Change “Category” to “Section”. Press “Edit”, select “PIntPRG” and press “Remove”. From this window the address of each section can be also modified. After all the changes are made press OK two times.
- At this point the files extracted from the zip file located in the “Software Tools” section have to be added into the project. Copy all the files from the archive into the project folder.
- Now, the files have to be included in the project. Use the key sequence Alt, P, A to open the “Add files to project ‘ADIEvalBoard’” window. Navigate into ADI folder. From the “Files of type” drop-down list, select “Project Files”. Select all the copied files and press Add.
- Now, the project is ready to be built. Press F7. The message after the Build Process is finished has to be “0 Errors, 0 Warnings”. To run the program on the board, you have to download the firmware into the microprocessor’s memory.
More information
- Example questions:
- An error occurred while fetching this feed: http://ez.analog.com/community/feeds/allcontent/atom?community=2077
- AD5160-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7193-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5541A-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7091R-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD74xx-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5933-瑞薩微控制器平臺的無操作系統驅動程序
- ADXL345-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7780-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD5781-適用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7980-適用于微芯片微控制器平臺的無操作系統驅動程序
- ADXL362-用于瑞薩微控制器平臺的無操作系統驅動程序
- ADP5589-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD799x-用于瑞薩微控制器平臺的無操作系統驅動程序
- ADXRS453-用于瑞薩微控制器平臺的無操作系統驅動程序
- AD7156-適用于瑞薩微控制器平臺的無操作系統驅動程序
- 瑞薩CTSU程序在向嵌入式OS操作系統移植時的注意事項 205次閱讀
- 深度解析全球操作系統格局 676次閱讀
- 實時時鐘為微控制器系統增加了精確的計時功能 1121次閱讀
- 了解和使用無操作系統和平臺驅動程序 1066次閱讀
- 瑞薩快速接入式物聯網平臺為快速原型開發提供構建模塊 547次閱讀
- 基于具有USB功能的STM32微控制器 3682次閱讀
- 微控制器的主要應用在哪里 8647次閱讀
- 嵌入式Linux內核的驅動程序開發是怎樣的 1415次閱讀
- 淺談電腦驅動程序的工作原理 詳解電腦驅動程序意義 2.9w次閱讀
- 基于嵌入式Linux內核的系統設備驅動程序開發設計 1113次閱讀
- 基于Linux2.6.30開發DS18B20的驅動程序的類型和文件操作接口函數詳解 1377次閱讀
- 基于STM32的數字PDA系統軟件系統設計 1480次閱讀
- 8155驅動程序 3057次閱讀
- 基于STM32ZET6控制器的數字PDA系統的設計 1504次閱讀
- 基于FPGA嵌入式系統的設備驅動開發 2260次閱讀
上傳資料賺積分下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
工商網監
評論