資料介紹
Table of Contents
AD9129 Evaluation Board, DAC-FMC Interposer & Xilinx ML-605 Reference Design
Introduction
The AD9129 is a 14-bit, high performance digital-to-analog converter (DAC) that provides a sample rate of 2.8GSPS. This reference design includes a DDS generator that drives the device. The programming is done via the USB-SPI interface.
Supported Devices
Supported Carriers
Quick Start Guide
The bit file provided combines the FPGA bit file and the SDK elf files. It may be used for a quick check on the system. All you need is the hardware and a PC running a UART terminal, ADI DAC software and the programmer (IMPACT).
Required Hardware
- ML605 board
- AD9129-EBZ board & Power supply
- DAC FMC interposer board
- Signal/Clock generator (2.4GHz)
- Spectrum Analyzer
Required Software
- Xilinx ISE 14.1 (Programmer (IMPACT) is sufficient for the demo and is available on Webpack).
- A UART terminal (Tera Term/Hyperterminal), Baud rate 57600.
- ADI DPG DAC Software Suite available here.
Bit file
- Download the gzip file and extract the sw/cf_ad9129_ebz.bit file.
Running Demo (SDK) Program
To begin make the following connections (see image below):
- Connect the AD9129-EBZ board to the FMC Interposer board.
- Connect the interposer board to the FMC-LPC connector of ML605 board.
- Connect power to ML605 and the AD9129-EBZ boards.
- Connect two USB cables from the PC to the JTAG and UART USB connectors on ML605.
- Connect a USB cable to the AD9129-EBZ board.
- Connect an external clock source to AD9129-EBZ board's J3 SMA connector.
- Connect a spectrum analyzer to AD9129-EBZ board's J1 SMA connector.
Setup the clock source to be 2.4GHz/0dBm. After the hardware setup, turn the power on to the ML605 and the AD9129-EBZ boards.
Start ADI- AD9129 SPI program (see screenshot below) and click on “Run Forever” button.
Start IMPACT, and initialze the JTAG chain. The program should recognize the Virtex 6 device. Start a UART terminal (set to 57600 baud rate) and then program the device.
If programming was successful, you should be seeing messages appear on the terminal as shown in figure below.
After DDS is enabled, disable and enable the DLL on the AD9129 SPI interface. You should see the spectrum analyzer displaying a 300MHz tone.
Using the reference design
Functional description
The reference design consists of a DDS module and a lvds interface.
The DDS module consists of a Xilinx IP core and a DDR-DDS. Internally the DDS runs at fDAC/3 clock. The DDR-DDS allows any pattern to be generated in the memory to be driven to the DAC. The output samples are interleaved and driven by the lvds interface.
Registers
Please see the regmap.txt file in the pcore directory.
Downloads
- ML605 Source files cf_ad9129_ebz_edk_14_4_2013_03_12.tar.gz
- ML605 SW/Bit files cf_ad9129_ebz_sw_14_4_2013_03_12.tar.gz
Only Xilinx coregen xco files are provided with the reference design. You must regenerate the IP core files using this file. See generating Xilinx netlist/verilog files from xco files for details.
- Questions? Ask Help & Support.
Tar file contents
The tar file contains, in most cases, the following files and/or directories. To rebuild the reference design simply double click the XMP file and run the tool. To build SDK, select a workspace and use the C file to build the elf file. Please refer to Xilinx EDK documentation for details.
license.txt | ADI license & copyright information. |
system.mhs | MHS file. |
system.xmp | XMP file (use this file to build the reference design). |
data/ | UCF file and/or DDR MIG project files. |
docs/ | Documentation files (Please note that this wiki page is the documentation for the reference design). |
sw/ | Software (Xilinx SDK) & bit file(s). |
cf_lib/edk/pcores/ | Reference design core file(s) (Xilinx EDK). |
More information
- AD9129 IBIS型號
- FMC插入器&Xilinx KC705參考設計
- AD7656-1 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- FMC-Imageon Xilinx ML605參考設計
- ADC-FMC插入器&Xilinx ZC706參考設計
- AD9789評估板、DAC-FMC轉接器和Xilinx ML605參考設計
- AD971x/AD911x-DPG2 FMC轉接器和評估板/Xilinx ML-605參考設計
- AD9129評估板文檔
- AD9265本地FMC卡/ML605 Xilinx參考設計
- AD9434本地FMC卡和ML605 Xilinx參考設計
- AD9279評估板、ADC-FMC轉接器和Xilinx ML605參考設計
- AD9739A評估板、DAC-FMC插入器和Xilinx參考設計
- AD9467評估板、ADC-FMC插入器和Xilinx參考設計
- AD9122評估板、DAC-FMC插入器和Xilinx ML-605參考設計
- AN-1296:AD9129 電源優化
- 【GD32F470紫藤派開發板使用手冊】第四講 FMC-片內Flash擦寫讀實驗 1359次閱讀
- 基于Xilinx K7-410T的高速DAC之AD9129開發筆記(二) 772次閱讀
- 基于Xilinx K7-410T的高速DAC之AD9129開發筆記 1151次閱讀
- 系統演示平臺簡化了從評估到原型設計的過渡 809次閱讀
- Arm?ML處理器 嵌入式評估工具包介紹 8193次閱讀
- Xilinx FPGA的FMC介紹 5947次閱讀
- digilent FMC Pcam適配器介紹 2879次閱讀
- digilent FMC-HDMI:雙HDMI輸入擴展子板介紹 4507次閱讀
- 2.5 GSPS高性能數模轉換器——AD9739A DAC 4866次閱讀
- 關于FPGA的FMC接口的詳細介紹 1.2w次閱讀
- 詳解Xilinx公司Zynq? UltraScale+?MPSoC產品 3357次閱讀
- 采用Xilinx ML507評估平臺的APU增強型FPGA設計 1245次閱讀
- 基于FPGA的DMA讀寫設計及中斷控制 6239次閱讀
- 采用RFDAC的多頻段、多標準發射器設計 3185次閱讀
- Maxim為三款Xilinx FPGA參考設計提供電源管理方案 1210次閱讀
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多